No matter what kind of boat you have, the bottom needs to be kept clean

Bottom Boat Cleaning

No matter what kind of boat you run– power or sail, high speed or slow– with fuel costing what it does and optimum performance always a good thing, it literally pays to keep your bottom clean. This means not only the main hull, but your foils (rudders, keels, skegs) and running gear (props, shafts, struts). The hardest parts to keep clean are the most important– rudders and propellers. Usually these are bare metal, but even if painted they are susceptible to fouling. Any significant hard growth– meaning more than a very few barnacles– on a propeller will have a big, bad effect on a boat’s performance. Those barnacles get top priority. Whether you do the work your self, or have a diving company clean your bottom, it needs to be completed on a regular basis.

Burnish and shine all underwater metal as much as possible at the beginning of the season– the shinier and slicker it is when it goes into the water, the longer it will ward off growth. Here are some tips that will help keep a bottom clean and a boat faster and more fuel-efficient:

1. Don’t scrub ablative paint underwater. Modern bottom paints, either ablative or hard, already do a good job of keeping fouling away. Usually a fast run or a light sweep with a hand or soft sponge will help the paint shed any surface coating– but don’t wait too long between cleaning runs (see point No. 2). Ablative paints should not be scrubbed or abraded underwater, period. Scrubbing releases a high concentration of toxic material, and in fact there are plenty of local laws that prohibit underwater bottom paint cleaning, especially in enclosed waters. It’s time to repaint and haul the boat if you have any serious fouling where your ablative paint should be.

2. Prevention is a lot easier than cure. Once you’ve got barnacles, it’s very hard to get an ultra-smooth surface again– even when you scrape off the exoskeletons, much of the tenacious adhesive will remain. Don’t wait too long after launch to begin your prevention. Spend some time under the boat with a mask every couple of weeks. Again, you should be able to use your hand or a sponge to do most of the work, although a light-duty 3M pad will do a better job on dark stains above the waterline and on the boot top.

3. Hire a diver to do the work if you’re not comfortable underwater. It won’t take the diver much time or effort to sponge off the slime if the bottom is free of hard fouling to begin with. It will be expensive if he has to burn through two tanks scraping barnacles off the waterline or running gear with a putty knife. It will probably still cost less in the long run than the extra fuel necessary to drag all those barnacles through the water, whether on the hull or on the blades of a struggling propeller.

4. Wear work gloves. They protect your hands from barnacles and barked knuckles.

5. For hard growth use a thick-bladed putty knife, but be careful not to gouge or score other metals. The edges of a piece of two-by-four also work well for getting the worst of the fouling off, and unlike the putty knife, the two-by-four floats.

6. Be safe. Don’t go under the boat if conditions are choppy, or if there are nearby boats throwing wakes. Getting hit in the head by a plunging boat will ruin your day.

7. Use the conditions to your advantage. Start upstream and work your way down if there’s a current running. It will save a lot of energy if you can position the boat so that you can stand on the bottom while you clean. Also turn the boat to take advantage of the sun for extra visibility if possible.

8. Handholds along the topsides will save energy. There are suction-cup handles commercially available. A long bight of line tied bow-to-stern on each side will work, too. Be sure to pull the lines back aboard after your cleaning. If you forget them.), (They have a way of winding up in the prop.

9. Start with the running gear– the most important items (see above).

10. Clean all around the waterline. This is where slime, weedy growth, and stains accumulate the fastest. If you can just do the waterline down to an arm’s length underwater, without even putting your head under, you will have solved a lot of the problem and made the boat look better cosmetically. If possible work your way down from there, under the turn of the bilge, the chines, the counter, and on to the keel or skeg.

6 thoughts on “No matter what kind of boat you have, the bottom needs to be kept clean”

  1. This is a great post, and it is absolutely right. Not keeping their boat bottom clean is one of the biggest mistakes that a boat owner can make. And I have personally used the company you link to here in Charleston. Thanks for promoting them!

  2. I made a mess with my dad’s boat before. I strongly suggest to have your bottoms looked at by pros. He almost killed me back then,. LOL! but nice article you got there.

  3. That’s a hard task to do, I’m glad you posted it here. Gonna go sailing next few months and getting my stuff all together. Thanks!

    1. Great feature and I look forward to it for other collections. Are the various brands of solids all compatible? I’ve only used Kona Cottons but I’d like something with a higher thread count in the hopes that another brand might have less fraying. Any remksmendations?thanocPam

  4. Reading your blog gave me a lot of interesting info ,
    it deserves to go viral, you need some initial traffic only.
    How to get initial traffic??? Search for: masitsu’s tricks

    1. I was curious if you ever thought of changing the page layout of your website? Its very well written; I love what youve got to say. But maybe you could a little more in the way of content so people could connect with it better. Youve got an awful lot of text for only having one or two piutsrec. Maybe you could space it out better?

Leave a Reply

Your email address will not be published. Required fields are marked *